[[hacking:verbatim:dmesg]]

Bytes transferred = 8833880 (86cb58 hex)
## Booting image at 02000000 ...
   Image Name:   3.12.1-verbatim-19
   Created:      2014-02-15  21:14:24 UTC
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    1940443 Bytes =  1.9 MB
   Load Address: 00008000
   Entry Point:  00008000
   Verifying Checksum ... OK
OK
## Loading Ramdisk Image at 03000000 ...
   Image Name:   initramfs--3.12-1-kirkwood
   Created:      2014-02-08  17:55:26 UTC
   Image Type:   ARM Linux RAMDisk Image (gzip compressed)
   Data Size:    8833816 Bytes =  8.4 MB
   Load Address: 03000000
   Entry Point:  03000000
   Verifying Checksum ... OK

Starting kernel ...

Uncompressing Linux... done, booting the kernel.
[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Initializing cgroup subsys cpuset
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Initializing cgroup subsys cpuacct
[    0.000000] Linux version 3.12-1-kirkwood (debian-kernel@lists.debian.org) (gcc version 4.8.2 (Debian 4.8.2-10) ) #1 Debian 3.12.9-1 (2014-02-01)
[    0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=00053977
[    0.000000] CPU: VIVT data cache, VIVT instruction cache
[    0.000000] Machine: Marvell Kirkwood (Flattened Device Tree), model: Verbatim PowerBay
[    0.000000] bootconsole [earlycon0] enabled
[    0.000000] Memory policy: ECC disabled, Data cache writeback
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 65024
[    0.000000] Kernel command line: mtdparts=orion_nand:0x000e0000@0x00000000(u-boot)ro,0x1d73c0@0x000e0000(uImage),0x86cb58@0x2b73c0(uInitrd),-@0xb23f18(rootfs) console=ttyS0,115200 verbose mem=256M root=/dev/ram ip=off earlyprintk
[    0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[    0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Memory: 245308K/262144K available (3648K kernel code, 311K rwdata, 1280K rodata, 185K init, 412K bss, 16836K reserved)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
[    0.000000]     vmalloc : 0xd0800000 - 0xff000000   ( 744 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xd0000000   ( 256 MB)
[    0.000000]     modules : 0xbf000000 - 0xc0000000   (  16 MB)
[    0.000000]       .text : 0xc0008000 - 0xc04d8434   (4930 kB)
[    0.000000]       .init : 0xc04d9000 - 0xc05077f4   ( 186 kB)
[    0.000000]       .data : 0xc0508000 - 0xc0555ea0   ( 312 kB)
[    0.000000]        .bss : 0xc0555ea0 - 0xc05bd250   ( 413 kB)
[    0.000000] NR_IRQS:114
[    0.000000] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 21474ms
[    0.000000] Console: colour dummy device 80x30
[    0.004836] Calibrating delay loop... 1191.93 BogoMIPS (lpj=2383872)
[    0.034901] pid_max: default: 32768 minimum: 301
[    0.039681] Security Framework initialized
[    0.043877] Yama: disabled by default; enable with sysctl kernel.yama.*
[    0.050624] Mount-cache hash table entries: 512
[    0.057599] Initializing cgroup subsys memory
[    0.062103] Initializing cgroup subsys devices
[    0.066644] Initializing cgroup subsys freezer
[    0.071173] Initializing cgroup subsys net_cls
[    0.075697] Initializing cgroup subsys blkio
[    0.080049] Initializing cgroup subsys perf_event
[    0.084906] CPU: Testing write buffer coherency: ok
[    0.090213] Setting up static identity map for 0xc0372eb0 - 0xc0372eec
[    0.098167] devtmpfs: initialized
[    0.102687] pinctrl core: initialized pinctrl subsystem
[    0.108388] regulator-dummy: no parameters
[    0.112867] NET: Registered protocol family 16
[    0.117789] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.125300] cpuidle: using governor ladder
[    0.129500] cpuidle: using governor menu
[    0.133578] Kirkwood: MV88F6281-A0, TCLK=0.
[    0.137957] Feroceon L2: Enabling L2
[    0.141653] Feroceon L2: Cache support initialised.
[    0.150155] No ATAGs?
[    0.154342] bio: create slab <bio-0> at 0
[    0.159151] SATA0 Power: Failed to request enable GPIO39: -517
[    0.165146] reg-fixed-voltage 1.regulator: Failed to register regulator: -517
[    0.172349] platform 1.regulator: Driver reg-fixed-voltage requests probe deferral
[    0.180103] SATA1 Power: Failed to request enable GPIO40: -517
[    0.186067] reg-fixed-voltage 2.regulator: Failed to register regulator: -517
[    0.193272] platform 2.regulator: Driver reg-fixed-voltage requests probe deferral
[    0.201012] SATA2 Power: Failed to request enable GPIO41: -517
[    0.206977] reg-fixed-voltage 3.regulator: Failed to register regulator: -517
[    0.214181] platform 3.regulator: Driver reg-fixed-voltage requests probe deferral
[    0.221919] SATA3 Power: Failed to request enable GPIO42: -517
[    0.227876] reg-fixed-voltage 4.regulator: Failed to register regulator: -517
[    0.235081] platform 4.regulator: Driver reg-fixed-voltage requests probe deferral
[    0.242887] vgaarb: loaded
[    0.246337] Switched to clocksource orion_clocksource
[    0.266534] NET: Registered protocol family 2
[    0.271602] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
[    0.278778] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
[    0.285219] TCP: Hash tables configured (established 2048 bind 2048)
[    0.291733] TCP: reno registered
[    0.295053] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.300969] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.307494] NET: Registered protocol family 1
[    0.312136] Unpacking initramfs...
[    1.065570] Freeing initrd memory: 8620K (c3001000 - c386c000)
[    1.071559] NetWinder Floating Point Emulator V0.97 (double precision)
[    1.079129] audit: initializing netlink socket (disabled)
[    1.084656] type=2000 audit(1.032:1): initialized
[    1.202742] VFS: Disk quotas dquot_6.5.2
[    1.206808] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    1.213523] jffs2: version 2.2. (NAND) (SUMMARY)  © 2001-2006 Red Hat, Inc.
[    1.220832] msgmni has been set to 495
[    1.226490] alg: No test for stdrng (krng)
[    1.230743] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[    1.238316] io scheduler noop registered
[    1.242322] io scheduler deadline registered
[    1.246699] io scheduler cfq registered (default)
[    1.252134] kirkwood-pinctrl f1010000.pinctrl: registered pinctrl driver
[    1.259189] mv_xor f1060800.xor: Marvell shared XOR driver
[    1.282383] mv_xor f1060800.xor: Marvell XOR: ( xor cpy )
[    1.306376] mv_xor f1060800.xor: Marvell XOR: ( xor cpy )
[    1.311972] mv_xor f1060900.xor: Marvell shared XOR driver
[    1.334381] mv_xor f1060900.xor: Marvell XOR: ( xor cpy )
[    1.358381] mv_xor f1060900.xor: Marvell XOR: ( xor cpy )
[    1.364178] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[    1.371440] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 33, base_baud = 12500000) is a 16550A
[    1.380486] console [ttyS0] enabled, bootconsole disabled
[    1.380486] console [ttyS0] enabled, bootconsole disabled
[    1.392564] NAND device: Manufacturer ID: 0xec, Chip ID: 0xf1 (Samsung NAND 128MiB 3,3V 8-bit), 128MiB, page size: 2048, OOB size: 64
[    1.404644] Scanning device for bad blocks
[    1.411554] Bad eraseblock 37 at 0x0000004a0000
[    1.420373] Bad eraseblock 95 at 0x000000be0000
[    1.444351] Bad eraseblock 358 at 0x000002cc0000
[    1.453327] Bad eraseblock 417 at 0x000003420000
[    1.460456] Bad eraseblock 451 at 0x000003860000
[    1.471870] Bad eraseblock 543 at 0x0000043e0000
[    1.501400] Bad eraseblock 880 at 0x000006e00000
[    1.506158] Bad eraseblock 882 at 0x000006e40000
[    1.510920] Bad eraseblock 884 at 0x000006e80000
[    1.522332] Bad eraseblock 976 at 0x000007a00000
[    1.527824] Bad eraseblock 988 at 0x000007b80000
[    1.533983] Bad eraseblock 1009 at 0x000007e20000
[    1.539762] 4 cmdlinepart partitions found on MTD device orion_nand
[    1.546064] Creating 4 MTD partitions on "orion_nand":
[    1.551239] 0x000000000000-0x0000000e0000 : "u-boot"
[    1.557088] 0x0000000e0000-0x0000002b73c0 : "uImage"
[    1.562094] mtd: partition "uImage" doesn't end on an erase block -- force read-only
[    1.570719] 0x0000002b73c0-0x000000b23f18 : "uInitrd"
[    1.575814] mtd: partition "uInitrd" doesn't start on an erase block boundary -- force read-only
[    1.585470] 0x000000b23f18-0x000008000000 : "rootfs"
[    1.590474] mtd: partition "rootfs" doesn't start on an erase block boundary -- force read-only
[    1.600482] mousedev: PS/2 mouse device common for all mice
[    2.606380] rtc-mv f1010300.rtc: internal RTC not ticking
[    2.611906] i2c /dev entries driver
[    2.621707] TCP: cubic registered
[    2.625114] NET: Registered protocol family 10
[    2.630231] mip6: Mobile IPv6
[    2.633245] NET: Registered protocol family 17
[    2.637732] mpls_gso: MPLS GSO support
[    2.642021] registered taskstats version 1
[    2.646879] SATA0 Power: 5000 mV 
[    2.650484] SATA1 Power: 5000 mV 
[    2.654008] SATA2 Power: 5000 mV 
[    2.657572] SATA3 Power: 5000 mV 
[    2.661160] /build/linux-qWXwPY/linux-3.12.9/drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[    2.671147] Freeing unused kernel memory: 184K (c04d9000 - c0507000)
Loading, please wait...
[    2.742902] systemd-udevd[49]: starting version 204
[    3.015098] libphy: orion_mdio_bus: probed
[    3.023798] usbcore: registered new interface driver usbfs
[    3.042056] SCSI subsystem initialized
[    3.062050] usbcore: registered new interface driver hub
[    3.078566] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4
[    3.102808] usbcore: registered new device driver usb
[    3.109064] mvsdio f1090000.mvsdio: no pins associated
[    3.631431] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    3.650403] mvsdio f1090000.mvsdio: lacking card detect (fall back to polling)
[    3.675632] ehci-orion: EHCI orion driver
[    3.679832] kirkwood-pinctrl f1010000.pinctrl: unsupported function sata0 on pin mpp20
[    3.707841] pinctrl core: failed to register map default (0): invalid type given
[    3.715323] mvsdio f1090000.mvsdio: unhandled interrupt status=0x8810 en=0x0000 pio=0
[    3.745949] sata_mv f1080000.sata: slots 32 ports 4
[    3.784437] scsi0 : sata_mv
[    3.793058] scsi1 : sata_mv
[    3.795906] mvsdio f1090000.mvsdio: unhandled interrupt status=0x8810 en=0x0000 pio=0
[    3.809765] scsi2 : sata_mv
[    3.812619] mvsdio f1090000.mvsdio: unhandled interrupt status=0x8810 en=0x0000 pio=0
[    3.821129] scsi3 : sata_mv
[    3.824508] ata1: SATA max UDMA/133 irq 25
[    3.828653] ata2: SATA max UDMA/133 irq 25
[    3.832782] ata3: SATA max UDMA/133 irq 25
[    3.836906] ata4: SATA max UDMA/133 irq 25
[    3.841485] orion-ehci f1050000.ehci: EHCI Host Controller
[    3.847048] mvsdio f1090000.mvsdio: unhandled interrupt status=0x8810 en=0x0000 pio=0
[    3.855970] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1
[    3.863703] mvsdio f1090000.mvsdio: unhandled interrupt status=0x8810 en=0x0000 pio=0
[    3.872748] orion-ehci f1050000.ehci: irq 23, io mem 0xf1050000
[    4.378380] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00
[    4.386049] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 00:50:43:3c:3b:5d
[    4.395019] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[    4.401866] mvsdio f1090000.mvsdio: unhandled interrupt status=0x8810 en=0x0000 pio=0
[    4.409749] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    4.417014] usb usb1: Product: EHCI Host Controller
[    4.421922] usb usb1: Manufacturer: Linux 3.12-1-kirkwood ehci_hcd
[    4.428140] usb usb1: SerialNumber: f1050000.ehci
[    4.439619] hub 1-0:1.0: USB hub found
[    4.443460] hub 1-0:1.0: 1 port detected
[    4.646460] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl F300)
[    4.653451] ata1.15: Port Multiplier 1.2, 0x11ab:0x4140 r193, 4 ports, feat 0x5/0x1f
[    4.670560] ata1.00: hard resetting link
[    4.758386] usb 1-1: new high-speed USB device number 2 using orion-ehci
[    4.894875] usb 1-1: New USB device found, idVendor=0409, idProduct=005a
[    4.901630] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[    4.911543] hub 1-1:1.0: USB hub found
[    4.916899] hub 1-1:1.0: 2 ports detected
[    4.995114] ata1.01: hard resetting link
[    5.214624] usb 1-1.2: new high-speed USB device number 3 using orion-ehci
[    5.319102] ata1.02: hard resetting link
[    5.327243] usb 1-1.2: New USB device found, idVendor=0781, idProduct=557c
[    5.334175] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[    5.341538] usb 1-1.2: Product: Cruzer Orbit
[    5.345841] usb 1-1.2: Manufacturer: SanDisk
[    5.350140] usb 1-1.2: SerialNumber: 4C530009121106109304
[    5.369500] usb-storage 1-1.2:1.0: USB Mass Storage device detected
[    5.376074] scsi4 : usb-storage 1-1.2:1.0
[    5.381581] usbcore: registered new interface driver usb-storage
[    5.667113] ata1.03: hard resetting link
[    5.991244] ata1: EH complete
[    6.314363] ata2: SATA link down (SStatus 0 SControl F300)
[    6.379716] scsi 4:0:0:0: Direct-Access     SanDisk  Cruzer Orbit     1.27 PQ: 0 ANSI: 6
[    6.414667] sd 4:0:0:0: [sda] 15633408 512-byte logical blocks: (8.00 GB/7.45 GiB)
[    6.423768] sd 4:0:0:0: [sda] Write Protect is off
[    6.429267] sd 4:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[    6.444895]  sda: sda1 sda2 sda3 < sda5 >
[    6.453271] sd 4:0:0:0: [sda] Attached SCSI disk
[    7.346357] ata3: failed to resume link (SControl 0)
[    7.351367] ata3: SATA link down (SStatus 0 SControl 0)
[    8.382358] ata4: failed to resume link (SControl 0)
[    8.387370] ata4: SATA link down (SStatus 0 SControl 0)
[    8.435863] sd 4:0:0:0: Attached scsi generic sg0 type 0
Begin: Loading essential drivers ... done.
Begin: Running /scripts/init-premount ... done.
Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done.
Begin: Running /scripts/local-premount ... done.
[    8.929380] EXT4-fs (sda2): mounted filesystem with ordered data mode. Opts: (null)
Begin: Running /scripts/local-bottom ... done.
done.
Begin: Running /scripts/init-bottom ... done.
INIT: version 2.88 booting
[info] Using makefile-style concurrent boot in runlevel S.
[....] Starting the hotplug events dispatcher: udevd[   10.198898] systemd-udevd[274]: starting version 204
. ok 
[....] Synthesizing the initial hotplug events...[   10.442818] input: gpio_keys.4 as /devices/gpio_keys.4/input/input0
[   10.629032] orion_wdt: Initial timeout 21 sec
[   10.641415] lm75 0-0049: hwmon0: sensor 'lm75'
done.
[....] Waiting for /dev to be fully populated...[   11.040224] alg: hash: Test 1 failed for mv-hmac-sha1
[   11.045326] 00000000: 0c aa 9f d5 37 c3 79 3a 91 d9 21 5f 42 2b 2c 24
[   11.051815] 00000010: b7 c3 16 0c
done.
[....] Activating swap...[   11.856403] Adding 383996k swap on /dev/sda5.  Priority:-1 extents:1 across:383996k 
done.
[   11.952162] EXT4-fs (sda2): re-mounted. Opts: (null)
[....] Checking root file system...fsck from util-linux 2.20.1
/dev/sda2: clean, 108716/449680 files, 581951/1795328 blocks
done.
[   12.305076] EXT4-fs (sda2): re-mounted. Opts: errors=remount-ro
[ ok ] Cleaning up temporary files... /tmp.
[info] Loading kernel module gpio_keys.
[info] Loading kernel module loop.
[   13.406496] loop: module loaded
[info] Loading kernel module lm75.
[info] Loading kernel module gpio_fan.
[   13.504316] gpio-fan gpio_fan.5: GPIO fan initialized
[ ok ] Activating lvm and md swap...done.
[....] Checking file systems...fsck from util-linux 2.20.1
/dev/sda1: clean, 17/124496 files, 27791/248832 blocks
done.
[....] Mounting local filesystems...[   14.196681] EXT4-fs (sda1): mounting ext2 file system using the ext4 subsystem
[   14.210299] EXT4-fs (sda1): mounted filesystem without journal. Opts: (null)
done.
[ ok ] Activating swapfile swap...done.
[ ok ] Cleaning up temporary files....
[ ok ] Setting kernel variables ...done.
[....] Configuring network interfaces...[   15.663398] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
done.
[ ok ] Starting rpcbind daemon....
[....] Starting NFS common utilities: statd[   16.349342] RPC: Registered named UNIX socket transport module.
[   16.355321] RPC: Registered udp transport module.
[   16.360057] RPC: Registered tcp transport module.
[   16.364789] RPC: Registered tcp NFSv4.1 backchannel transport module.
[   16.390409] FS-Cache: Loaded
[   16.430885] FS-Cache: Netfs 'nfs' registered for caching
[   16.487049] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ ok pd.
[ ok ] Cleaning up temporary files....
[ ok ] Setting sensors limits.
[ ok ] Starting qcontrol daemon: qcontrol.
[....] Setting up X socket directories... /tmp/.X11-unix /tmp/.ICE-unix[   17.336861] mv643xx_eth_port mv643xx_eth_port.0 eth0: link up, 100 Mb/s, full duplex, flow control disabled
[   17.346734] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
. ok 
INIT: Entering runlevel: 2
[info] Using makefile-style concurrent boot in runlevel 2.
[ ok ] Starting NFS common utilities: statd idmapd.
[ ok ] Starting fan speed regulator: fancontrol.
[warn] Not starting NFS kernel daemon: no exports. ... (warning).
[ ok ] Starting NetBIOS name server: nmbd.
[ ok ] Starting enhanced syslogd: rsyslogd.
[ ok ] Starting deferred execution scheduler: atd.
[ ok ] Starting periodic command scheduler: cron.
[ ok ] Starting system message bus: dbus.
[ ok ] Starting MTA: exim4.
[ ok ] Starting sensor daemon: sensord.
[ ok ] Starting SMB/CIFS daemon: smbd.
[ ok ] Starting OpenBSD Secure Shell server: sshd.
[ ok ] Starting the Winbind daemon: winbind.
[info] System boot completed.
Error connecting to socket: No such file or directory

Debian GNU/Linux jessie/sid debian ttyS0

debian login: root
Password: 
lLast login: Sat Feb 15 22:12:16 CET 2014 on ttyS0
Linux debian 3.12-1-kirkwood #1 Debian 3.12.9-1 (2014-02-01) armv5tel
  • hacking/verbatim/dmesg.txt
  • Last modified: 2016/12/28 21:15
  • (external edit)